ElementRef

ARGO-HYTOS · Filter Elements · inline line

S2.1023-08K filter element: specifications & equivalents

The S2.1023-08K is a ARGO-HYTOS inline-line hydraulic filter element, built with screen media, sized 99.5 × 229 mm OD × length (ID 67.5 mm). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 99.5 × 229 mm
Inside diameter 67.5 mm
Media Screen
Collapse / burst 3 bar
Line type inline
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

Dimensions, filter fineness and collapse pressure are taken from the ARGO-HYTOS product portal. Beta efficiency per ISO 16889 and seal material vary by execution — verify against the current ARGO-HYTOS data sheet before ordering.

Specification table

ParameterValue
Filter type inline line
Media Screen
Outside diameter OD 99.5 mm
Inside diameter ID 67.5 mm
Length 229 mm
End caps open-ended cartridge element
Collapse / burst pressure 3 bar
Integral bypass valve none (housing/valve-dependent)
Mass 580 g
Manufacturer part no. 15368300
Source catalog ARGO-HYTOS: ARGO-HYTOS product portal (portal.argo-hytos.com)
Last verified2026-09-28

Sources: ARGO-HYTOS — ARGO-HYTOS product portal (portal.argo-hytos.com) — accessed 2026-09-28.

ARGO-HYTOS® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized ARGO-HYTOS distributor.

Dimensions & series range

Outside diameter99.5 mm (3.917 in)
Inside diameter67.5 mm (2.657 in)
Overall length229 mm (9.016 in)

All 100×229 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the S2.1023-08K model number is decoded

  • S2.1023-08KARGO-HYTOS filter element part number (Screen Element) per the official product portal.
  • 99.5 mmOuter diameter.
  • 67.5 mmInner diameter.
  • 229 mmElement length.
  • 3 barElement collapse pressure rating.
  • ScreenFilter media.

Typical equipment & applications

  • Replacement element for ARGO-HYTOS hydraulic filter housings
  • Mobile and industrial hydraulic circuits

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the S2.1023-08K filter element?
The published envelope is 99.5 mm OD × 229 mm length with a 67.5 mm inside diameter (3.917 × 9.016 in × 2.657 in ID). Confirm against the housing drawing before ordering.
What replaces the S2.1023-08K filter element?
Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.
How do I read the S2.1023-08K part number?
See the designation decoder above: each segment of AHS2102308K encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 3 catalog element(s) share the 100×229 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

P2.1023-00K ARGO-HYTOS · 50 µm S2.1023-10K ARGO-HYTOS · 75 µm S2.1023-15K ARGO-HYTOS · 40 µm

Other models in the Filter Elements series

All 662 →
D 020.1300S D 020.1301S F2.1217-56K1 F2.1217-58K1 F2.1234-26K1 118×330 mm · 10 µm F2.1234-28K1 118×330 mm · 16 µm F2.1250-06K1 118×498 mm · 10 µm F2.1250-08K1 F3.0510-56K1 46×107 mm · 10 µm F3.0510-58K1 46×107 mm · 16 µm

Reviewed & verified by the ElementRef engineering desk against ARGO-HYTOS on 2026-09-28. Read our editorial & correction policy.