Fleetguard · HF Hydraulic · inline line
HF29063 filter element: specifications & equivalents
The HF29063 is a Fleetguard inline-line hydraulic filter element, sized 120 × 297.5 mm OD × length, rated at 10 µm absolute (10 µm at β75(c); 11 µm at β200(c) per ISO 16889). Verify against the current manufacturer data sheet before ordering.
Specifications and cross-references are taken from the Fleetguard online catalog API. Where both TWA and Beta ratings are published the conventions differ — verify cleanliness targets, collapse rating and seal configuration against the current Fleetguard data sheet before ordering.
Specification table
| Parameter | Value |
|---|---|
| Filter type | inline line |
| Filtration rating | 10 µm |
| Rating basis | absolute |
| Beta ratio | 10 µm at β75(c); 11 µm at β200(c) per ISO 16889 |
| Outside diameter OD | 120 mm |
| Length | 297.5 mm |
| End caps | open-ended cartridge element |
| Integral bypass valve | none (housing/valve-dependent) |
| Manufacturer part no. | HF29063 |
| Source catalog | Cummins Filtration / Fleetguard: Fleetguard online product catalog (fleetguard.com) |
| Last verified | 2026-09-28 |
Sources: Cummins Filtration / Fleetguard — Fleetguard online product catalog (fleetguard.com) — accessed 2026-09-28.
Fleetguard® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Fleetguard distributor.
Dimensions & series range
| Outside diameter | 120 mm (4.724 in) |
| Overall length | 297.5 mm (11.713 in) |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
|
↔ YZ502317 page in verification queue | Aftermarket | partial | Fleetguard's online catalog lists YZ502317 as an interchange for HF29063. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting. |
|
↔ YZ502378 page in verification queue | Aftermarket | partial | Fleetguard's online catalog lists YZ502378 as an interchange for HF29063. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting. |
Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HF29063 model number is decoded
- HF29063Fleetguard HF-series hydraulic cartridge element part number.
- 297.5 mmOverall height.
- 120 mmLargest outside diameter.
- 10 µm at β75(c); 11 µm at β200(c) per ISO 16889Published efficiency ratings.
Typical equipment & applications
- Construction, agricultural and industrial hydraulic circuits
- Mobile-equipment hydraulic return and pressure lines
Selection pitfalls — read before you substitute
- “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
- Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
- End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.
Frequently asked questions
What are the dimensions of the HF29063 filter element?
What micron rating does HF29063 use?
What replaces the HF29063 filter element?
How do I read the HF29063 part number?
Is a same-envelope aftermarket element always a drop-in replacement?
How often should a hydraulic return-line element be replaced?
Other models in the HF Hydraulic series
All 2621 →Reviewed & verified by the ElementRef engineering desk against Cummins Filtration / Fleetguard on 2026-09-28. Read our editorial & correction policy.