ElementRef

HYDAC · Betamicron 4 D/DN · pressure line

0060 D 003 BH4HC /-SFREE filter element: specifications & equivalents

The 0060 D 003 BH4HC /-SFREE is a HYDAC pressure-line hydraulic filter element, built with bh/hc=betamicron® high collapse media, sized 48.3 × 83.8 mm OD × length (ID 22 mm), rated at 3 µm absolute (ßx(c) ≥ 1000 (HYDAC grade convention: β5(c) ≥ 1000)). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 48.3 × 83.8 mm
Inside diameter 22 mm
Filtration rating 3 µm abs.
Beta rating ßx(c) ≥ 1000 (HYDAC grade convention: β5(c) ≥ 1000)
Media BH/HC=Betamicron® High Collapse
Collapse / burst 210 bar
Line type pressure
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

ParameterValue
Filter type pressure line
Media BH/HC=Betamicron® High Collapse
Filtration rating 3 µm
Rating basis absolute
Beta ratio ßx(c) ≥ 1000 (HYDAC grade convention: β5(c) ≥ 1000)
Outside diameter OD 48.3 mm
Inside diameter ID 22 mm
Length 83.8 mm
End caps open-ended cartridge element
Flow direction outside-in
Collapse / burst pressure 210 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (Buna-N)
Operating temperature -30 to 100 °C
Source catalog HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter48.3 mm (1.902 in)
Inside diameter22 mm (0.866 in)
Overall length83.8 mm (3.299 in)

All 48×84 mm interchange elements →

Cross references & equivalents

No catalog-verified cross references yet. This model is in the manual verification queue — request a verified equivalent.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 0060 D 003 BH4HC /-SFREE model number is decoded

  • 0060 D 003 BH4HC /-SFREEHYDAC Type D filter element ordering code per the HYDAC electronic catalog (s16).
  • BH/HC=Betamicron® High CollapseFilter media and collapse family as printed in the catalog.
  • 3 µmAbsolute filter rating per the HYDAC catalog.
  • ßx(c) ≥ 1000Beta ratio rating as printed in the catalog.
  • 48.3 mmOutside diameter.
  • 22 mmInner diameter.
  • 83.8 mmElement length.
  • 210 barElement collapse (differential pressure) rating.
  • Nitrile (Buna-N)Seal compound.

Typical equipment & applications

  • Pressure-line filtration for HYDAC DF/DFF and equivalent housings
  • Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • Fine 3 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0060 D 003 BH4HC /-SFREE filter element?
The published envelope is 48.3 mm OD × 83.8 mm length with a 22 mm inside diameter (1.902 × 3.299 in × 0.866 in ID). Confirm against the housing drawing before ordering.
What micron rating does 0060 D 003 BH4HC /-SFREE use?
This element is rated 3 µm absolute — ßx(c) ≥ 1000 (HYDAC grade convention: β5(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 0060 D 003 BH4HC /-SFREE filter element?
Cross references are being verified for this model — use the inquiry form and the engineering desk will confirm equivalents.
How do I read the 0060 D 003 BH4HC /-SFREE part number?
See the designation decoder above: each segment of 0060D003BH4HCSFREE encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 25 catalog element(s) share the 48×84 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

HF30187 Fleetguard HF30693 Fleetguard 0060 D 003 BH4HC HYDAC · 3 µm 0060 D 003 BH4HC /-V HYDAC · 3 µm 0060 D 003 ON HYDAC · 3 µm 0060 D 005 BH4HC HYDAC · 5 µm 0060 D 005 BH4HC /-SFREE HYDAC · 5 µm 0060 D 005 BH4HC /-V HYDAC · 5 µm 0060 D 005 ON HYDAC · 5 µm 0060 D 005 ON /-V HYDAC · 5 µm

Other models in the Betamicron 4 D/DN series

All 809 →
0015 D 010 BN4HC 35×42 mm · 10 µm 0030 D 003 BH4HC 36×94 mm · 3 µm 0030 D 003 BH4HC /-V 36×94 mm · 3 µm 0030 D 003 BN4HC 36×94 mm · 3 µm 0030 D 003 BN4HC /-V 36×94 mm · 3 µm 0030 D 005 BH4HC 36×94 mm · 5 µm 0030 D 005 BH4HC /-V 36×94 mm · 5 µm 0030 D 005 BN4HC 36×94 mm · 5 µm 0030 D 010 BH4HC 36×94 mm · 10 µm 0030 D 010 BN4HC 36×94 mm · 10 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.