HYDAC · Betamicron 4 D/DN · pressure line

0075 D 010 ON filter element: specifications & equivalents

Q: What are the dimensions of the 0075 D 010 ON filter element?

The published envelope is 55.9 mm OD × 170.2 mm length with a 26 mm inside diameter (2.201 × 6.701 in × 1.024 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does 0075 D 010 ON use?

This element is rated 10 µm absolute — β10 > 1000 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The 0075 D 010 ON is a HYDAC pressure-line hydraulic filter element, built with on=optimicron low-press. media, sized 55.9 × 170.2 mm OD × length (ID 26 mm), rated at 10 µm absolute (β10 > 1000 (HYDAC grade convention: β12(c) ≥ 1000)). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 55.9 × 170.2 mm

Inside diameter 26 mm

Filtration rating 10 µm abs.

Beta rating β 10 > 1000 (HYDAC grade convention: β12(c) ≥ 1000)

Media ON=Optimicron low-press.

Collapse / burst 20 bar

Line type pressure

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

Parameter	Value
Filter type	pressure line
Media	ON=Optimicron low-press.
Filtration rating	10 µm
Rating basis	absolute
Beta ratio	β10 > 1000 (HYDAC grade convention: β12(c) ≥ 1000)
Outside diameter OD	55.9 mm
Inside diameter ID	26 mm
Length	170.2 mm
End caps	open-ended cartridge element
Flow direction	outside-in
Collapse / burst pressure	20 bar
Integral bypass valve	none (housing/valve-dependent)
Seal material	Nitrile (Buna-N)
Operating temperature	-30 to 100 °C
Source catalog	HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified	2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter	55.9 mm (2.201 in)
Inside diameter	26 mm (1.024 in)
Overall length	170.2 mm (6.701 in)

All 56×170 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ 02.0075 D.10VG.30.HC.E.P	Eaton / Internormen	partial	Eaton's filtration cross-reference lists 0075D010ON (Hydac) as an interchange for 02.0075 D.10VG.30.HC.E.P. Envelope cross-reference; verify micron grade, delta-P rating and seal configuration before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 0075 D 010 ON model number is decoded

0075 D 010 ONHYDAC Type D filter element ordering code per the HYDAC electronic catalog (s16).
ON=Optimicron low-press.Filter media and collapse family as printed in the catalog.
10 µmAbsolute filter rating per the HYDAC catalog.
β10 > 1000Beta ratio rating as printed in the catalog.
55.9 mmOutside diameter.
26 mmInner diameter.
170.2 mmElement length.
20 barElement collapse (differential pressure) rating.
Nitrile (Buna-N)Seal compound.

Typical equipment & applications

Pressure-line filtration for HYDAC DF/DFF and equivalent housings
Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0075 D 010 ON filter element?

The published envelope is 55.9 mm OD × 170.2 mm length with a 26 mm inside diameter (2.201 × 6.701 in × 1.024 in ID). Confirm against the housing drawing before ordering.

What micron rating does 0075 D 010 ON use?

This element is rated 10 µm absolute — β10 > 1000 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the 0075 D 010 ON filter element?

1 partial match(es) requiring parameter review

How do I read the 0075 D 010 ON part number?

See the designation decoder above: each segment of 0075D010ON encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic return-line element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 8 catalog element(s) share the 56×170 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

02.0075 D.10VG.30.HC.E.P Eaton / Internormen · 10 µm HF29052 Fleetguard 0075 D 003 ON HYDAC · 3 µm 0075 D 005 ON HYDAC · 5 µm 0075 D 010 BH4HC HYDAC · 10 µm 0075 D 010 BN4HC /-SFREE HYDAC · 10 µm 0075 D 010 MM HYDAC · 10 µm 0075 D 020 ON HYDAC · 20 µm

Other models in the Betamicron 4 D/DN series

All 809 →

0015 D 010 BN4HC 35×42 mm · 10 µm 0030 D 003 BH4HC 36×94 mm · 3 µm 0030 D 003 BH4HC /-V 36×94 mm · 3 µm 0030 D 003 BN4HC 36×94 mm · 3 µm 0030 D 003 BN4HC /-V 36×94 mm · 3 µm 0030 D 005 BH4HC 36×94 mm · 5 µm 0030 D 005 BH4HC /-V 36×94 mm · 5 µm 0030 D 005 BN4HC 36×94 mm · 5 µm 0030 D 010 BH4HC 36×94 mm · 10 µm 0030 D 010 BN4HC 36×94 mm · 10 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.