ElementRef

HYDAC · Betamicron 4 R · return line

0160 R 010 P/HC /-KB filter element: specifications & equivalents

The 0160 R 010 P/HC /-KB is a HYDAC return-line hydraulic filter element, built with p/hc=polyester fleece / cellulose media, sized 73.7 × 144.8 mm OD × length (ID 34 mm), rated at 10 µm absolute (β12(c) ≥ 1000 per ISO 16889). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 73.7 × 144.8 mm
Inside diameter 34 mm
Filtration rating 10 µm abs.
Beta rating β 12(c) ≥ 1000 per ISO 16889
Media P/HC=Polyester Fleece / Cellulose
Collapse / burst 10 bar
Line type return
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

ParameterValue
Filter type return line
Media P/HC=Polyester Fleece / Cellulose
Filtration rating 10 µm
Rating basis absolute
Beta ratio β12(c) ≥ 1000 per ISO 16889
Outside diameter OD 73.7 mm
Inside diameter ID 34 mm
Length 144.8 mm
End caps open-ended cartridge element
Flow direction outside-in
Collapse / burst pressure 10 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (Buna-N)
Operating temperature -30 to 100 °C
Source catalog HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter73.7 mm (2.902 in)
Inside diameter34 mm (1.339 in)
Overall length144.8 mm (5.701 in)

All 74×145 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ RE-045-N-10-B-NBSTAUFFpartialSTAUFF Filter Interchange lists 0160 R 010 P/HC /-KB (HYDAC) as replaced by RE-045-N-10-B-NB. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 0160 R 010 P/HC /-KB model number is decoded

  • 0160 R 010 P/HC /-KBHYDAC Type R filter element ordering code per the HYDAC electronic catalog (s16).
  • P/HC=Polyester Fleece / CelluloseFilter media and collapse family as printed in the catalog.
  • 10 µmAbsolute filter rating per the HYDAC catalog.
  • 73.7 mmOutside diameter.
  • 34 mmInner diameter.
  • 144.8 mmElement length.
  • 10 barElement collapse (differential pressure) rating.
  • Nitrile (Buna-N)Seal compound.

Typical equipment & applications

  • Return-line filtration for HYDAC RF/RFM and equivalent housings
  • Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

  • A return-line element is not a pressure-line element: return cartridges (BN4HC low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
  • This element has no integral bypass — opening pressure is set by the housing’s reusable bypass valve. Confirm the valve setting (commonly 3.4 bar) is present before fitting.
  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0160 R 010 P/HC /-KB filter element?
The published envelope is 73.7 mm OD × 144.8 mm length with a 34 mm inside diameter (2.902 × 5.701 in × 1.339 in ID). Confirm against the housing drawing before ordering.
What micron rating does 0160 R 010 P/HC /-KB use?
This element is rated 10 µm absolute — β12(c) ≥ 1000 per ISO 16889. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 0160 R 010 P/HC /-KB filter element?
1 partial match(es) requiring parameter review
How do I read the 0160 R 010 P/HC /-KB part number?
See the designation decoder above: each segment of 0160R010PHCKB encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 24 catalog element(s) share the 74×145 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

0160 R 003 ON HYDAC · 3 µm 0160 R 003 ON /-B1 HYDAC · 3 µm 0160 R 003 ON /-B6 HYDAC · 3 µm 0160 R 003 ON /-KB HYDAC · 3 µm 0160 R 005 ON HYDAC · 5 µm 0160 R 005 ON /-B6 HYDAC · 5 µm 0160 R 005 ON /-KB HYDAC · 5 µm 0160 R 005 ON /-SO263 HYDAC · 5 µm 0160 R 010 ECON2 HYDAC · 10 µm 0160 R 010 ON HYDAC · 10 µm

Other models in the Betamicron 4 R series

All 929 →
0030 R 003 BN4HC 36×107 mm · 3 µm 0030 R 005 BN4HC 36×107 mm · 5 µm 0030 R 010 BN4HC 36×107 mm · 10 µm 0030 R 010 BN4HC /-B6 36×107 mm · 10 µm 0030 R 010 P/HC 36×107 mm · 10 µm 0030 R 010 P/HC /-B6 36×107 mm · 10 µm 0030 R 020 BN4HC 36×107 mm · 20 µm 0030 R 020 P/HC 36×107 mm · 20 µm 0030 R 025 W/HC 36×107 mm · 25 µm 0030 R 050 W/HC 36×107 mm · 50 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.