ElementRef

HYDAC · Betamicron 4 R · inline line

0201 RK 015 MM filter element: specifications & equivalents

The 0201 RK 015 MM is a HYDAC inline-line hydraulic filter element, built with mm=mobilemicron media, sized 88.9 × 325.1 mm OD × length (ID 40 mm), rated at 15 µm absolute (ßx(c) ≥ 200). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 88.9 × 325.1 mm
Inside diameter 40 mm
Filtration rating 15 µm abs.
Beta rating ßx(c) ≥ 200
Media MM=Mobilemicron
Collapse / burst 10 bar
Line type inline
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

ParameterValue
Filter type inline line
Media MM=Mobilemicron
Filtration rating 15 µm
Rating basis absolute
Beta ratio ßx(c) ≥ 200
Outside diameter OD 88.9 mm
Inside diameter ID 40 mm
Length 325.1 mm
End caps open-ended cartridge element
Flow direction outside-in
Collapse / burst pressure 10 bar
Integral bypass valve none (housing/valve-dependent)
Seal material Nitrile (Buna-N)
Operating temperature -30 to 100 °C
Source catalog HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter88.9 mm (3.500 in)
Inside diameter40 mm (1.575 in)
Overall length325.1 mm (12.799 in)

All 89×325 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ HD9012MANN-FILTERpartialMANN-FILTER's online catalog lists 0201 RK 015 MM (HYDAC) as a comparison number for HD9012. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 0201 RK 015 MM model number is decoded

  • 0201 RK 015 MMHYDAC Type RK filter element ordering code per the HYDAC electronic catalog (s16).
  • MM=MobilemicronFilter media and collapse family as printed in the catalog.
  • 15 µmAbsolute filter rating per the HYDAC catalog.
  • ßx(c) ≥ 200Beta ratio rating as printed in the catalog.
  • 88.9 mmOutside diameter.
  • 40 mmInner diameter.
  • 325.1 mmElement length.
  • 10 barElement collapse (differential pressure) rating.
  • Nitrile (Buna-N)Seal compound.

Typical equipment & applications

  • Multi-function and in-line hydraulic filtration
  • Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 0201 RK 015 MM filter element?
The published envelope is 88.9 mm OD × 325.1 mm length with a 40 mm inside diameter (3.500 × 12.799 in × 1.575 in ID). Confirm against the housing drawing before ordering.
What micron rating does 0201 RK 015 MM use?
This element is rated 15 µm absolute — ßx(c) ≥ 200. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 0201 RK 015 MM filter element?
1 partial match(es) requiring parameter review
How do I read the 0201 RK 015 MM part number?
See the designation decoder above: each segment of 0201RK015MM encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 2 catalog element(s) share the 89×325 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

0201 RK 005 MM HYDAC · 5 µm 0201 RK 010 MM HYDAC · 10 µm

Other models in the Betamicron 4 R series

All 929 →
0030 R 003 BN4HC 36×107 mm · 3 µm 0030 R 005 BN4HC 36×107 mm · 5 µm 0030 R 010 BN4HC 36×107 mm · 10 µm 0030 R 010 BN4HC /-B6 36×107 mm · 10 µm 0030 R 010 P/HC 36×107 mm · 10 µm 0030 R 010 P/HC /-B6 36×107 mm · 10 µm 0030 R 020 BN4HC 36×107 mm · 20 µm 0030 R 020 P/HC 36×107 mm · 20 µm 0030 R 025 W/HC 36×107 mm · 25 µm 0030 R 050 W/HC 36×107 mm · 50 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.