HYDAC · Betamicron 4 R · return line

1300 R 010 BN4AM filter element: specifications & equivalents

Q: What are the dimensions of the 1300 R 010 BN4AM filter element?

The published envelope is 142.2 mm OD × 482.6 mm length with a 96 mm inside diameter (5.598 × 19.000 in × 3.780 in ID). Confirm against the housing drawing before ordering.

Q: What micron rating does 1300 R 010 BN4AM use?

This element is rated 10 µm absolute — β10 > 200 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

The 1300 R 010 BN4AM is a HYDAC return-line hydraulic filter element, built with bn/am=beta/aquamicron media, sized 142.2 × 482.6 mm OD × length (ID 96 mm), rated at 10 µm absolute (β10 > 200 (HYDAC grade convention: β12(c) ≥ 1000)). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 142.2 × 482.6 mm

Inside diameter 96 mm

Filtration rating 10 µm abs.

Beta rating β 10 > 200 (HYDAC grade convention: β12(c) ≥ 1000)

Media BN/AM=Beta/Aquamicron

Collapse / burst 20 bar

Line type return

Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions, ratings and seal compound are taken directly from the HYDAC electronic catalog (catalog.hydac.com). Outside diameter and length are converted from the inch values printed on the catalog page; verify against the current HYDAC data sheet before ordering.

Specification table

Parameter	Value
Filter type	return line
Media	BN/AM=Beta/Aquamicron
Filtration rating	10 µm
Rating basis	absolute
Beta ratio	β10 > 200 (HYDAC grade convention: β12(c) ≥ 1000)
Outside diameter OD	142.2 mm
Inside diameter ID	96 mm
Length	482.6 mm
End caps	open-ended cartridge element
Flow direction	outside-in
Collapse / burst pressure	20 bar
Integral bypass valve	opens at 2.96 bar
Seal material	Nitrile (Buna-N)
Operating temperature	0 to 71 °C
Source catalog	HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified	2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter	142.2 mm (5.598 in)
Inside diameter	96 mm (3.780 in)
Overall length	482.6 mm (19.000 in)

All 142×483 mm interchange elements →

Cross references & equivalents

Equivalent model	Brand	Match level	Note
↔ RE-300-GA-10-B	STAUFF	partial	STAUFF Filter Interchange lists 1300 R 010 BN4AM (HYDAC) as replaced by RE-300-GA-10-B. Envelope dimensions are published; media grade and performance data are not — confirm before substituting in cleanliness-critical circuits.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 1300 R 010 BN4AM model number is decoded

1300 R 010 BN4AMHYDAC Type R filter element ordering code per the HYDAC electronic catalog (s16).
BN/AM=Beta/AquamicronFilter media and collapse family as printed in the catalog.
10 µmAbsolute filter rating per the HYDAC catalog.
β10 > 200Beta ratio rating as printed in the catalog.
142.2 mmOutside diameter.
96 mmInner diameter.
482.6 mmElement length.
20 barElement collapse (differential pressure) rating.
2.96 barIntegral bypass valve opening pressure.
Nitrile (Buna-N)Seal compound.

Typical equipment & applications

Return-line filtration for HYDAC RF/RFM and equivalent housings
Industrial and mobile hydraulic systems

Selection pitfalls — read before you substitute

A return-line element is not a pressure-line element: return cartridges (BN4HC low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
This execution carries an integral bypass valve (opens at 2.96 bar). The same envelope also exists without it, relying on the housing valve. Mixing the two strategies changes cold-start protection — match what was installed originally.
“10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 1300 R 010 BN4AM filter element?

The published envelope is 142.2 mm OD × 482.6 mm length with a 96 mm inside diameter (5.598 × 19.000 in × 3.780 in ID). Confirm against the housing drawing before ordering.

What micron rating does 1300 R 010 BN4AM use?

This element is rated 10 µm absolute — β10 > 200 (HYDAC grade convention: β12(c) ≥ 1000). Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.

What replaces the 1300 R 010 BN4AM filter element?

1 partial match(es) requiring parameter review

How do I read the 1300 R 010 BN4AM part number?

See the designation decoder above: each segment of 1300R010BN4AM encodes size, line type, filtration grade and media/collapse execution.

Is a same-envelope aftermarket element always a drop-in replacement?

No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.

How often should a hydraulic return-line element be replaced?

Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 73 catalog element(s) share the 142×483 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

1300 R 001 BN4HC HYDAC · 1 µm 1300 R 001 ON /-KB HYDAC · 1 µm 1300 R 003 BN4AM HYDAC · 3 µm 1300 R 003 BN4AM /-KB HYDAC · 3 µm 1300 R 003 BN4HC /-B4-KE50 HYDAC · 3 µm 1300 R 003 ON HYDAC · 3 µm 1300 R 003 ON /-B6 HYDAC · 3 µm 1300 R 003 ON /-KB HYDAC · 3 µm 1300 R 003 ON /-V-B6 HYDAC · 3 µm 1300 R 003 ON /-V-KB HYDAC · 3 µm

Other models in the Betamicron 4 R series

All 929 →

0030 R 003 BN4HC 36×107 mm · 3 µm 0030 R 005 BN4HC 36×107 mm · 5 µm 0030 R 010 BN4HC 36×107 mm · 10 µm 0030 R 010 BN4HC /-B6 36×107 mm · 10 µm 0030 R 010 P/HC 36×107 mm · 10 µm 0030 R 010 P/HC /-B6 36×107 mm · 10 µm 0030 R 020 BN4HC 36×107 mm · 20 µm 0030 R 020 P/HC 36×107 mm · 20 µm 0030 R 025 W/HC 36×107 mm · 25 µm 0030 R 050 W/HC 36×107 mm · 50 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.