ElementRef

HYDAC · Betamicron 4 R · return line

5.01.05 R 03 P filter element: specifications & equivalents

The 5.01.05 R 03 P is a HYDAC return-line hydraulic filter element, built with p=polyester fleece / cellulose media, sized 76.2 × 124.5 mm OD × length (ID 26.6 mm), rated at 3 µm absolute (β5(c) ≥ 1000 per ISO 16889). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 76.2 × 124.5 mm
Inside diameter 26.6 mm
Filtration rating 3 µm abs.
Beta rating β 5(c) ≥ 1000 per ISO 16889
Media P=Polyester Fleece / Cellulose
Collapse / burst 10 bar
Line type return
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.90.

HYDAC Betterfit element — dimensions and ratings are taken from catalog.hydac.com. This is HYDAC's drop-in replacement for a Schroeder element; the exact competitor part number is not published on the catalog page. Verify form/fit and micron grade against the competitor data sheet before substituting.

Specification table

ParameterValue
Filter type return line
Media P=Polyester Fleece / Cellulose
Filtration rating 3 µm
Rating basis absolute
Beta ratio β5(c) ≥ 1000 per ISO 16889
Outside diameter OD 76.2 mm
Inside diameter ID 26.6 mm
Length 124.5 mm
End caps open-ended cartridge element
Flow direction outside-in
Collapse / burst pressure 10 bar
Integral bypass valve opens at 3 bar
Seal material Nitrile (Buna-N)
Operating temperature -30 to 100 °C
Source catalog HYDAC Technology Corporation: HYDAC electronic product catalog (catalog.hydac.com)
Last verified2026-09-28

Sources: HYDAC Technology Corporation — HYDAC electronic product catalog (catalog.hydac.com) — accessed 2026-09-29.

HYDAC® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized HYDAC distributor.

Dimensions & series range

Outside diameter76.2 mm (3.000 in)
Inside diameter26.6 mm (1.047 in)
Overall length124.5 mm (4.902 in)

All 76×125 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ AZ1Schroeder IndustriespartialSchroeder online cross-reference (HYDAC); envelope match — verify grade and seals.
↔ AZ3Schroeder IndustriespartialSchroeder online cross-reference (HYDAC); envelope match — verify grade and seals.
↔ AZ5Schroeder IndustriespartialSchroeder online cross-reference (HYDAC); envelope match — verify grade and seals.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 5.01.05 R 03 P model number is decoded

  • 5.01.05 R 03 PHYDAC Betterfit filter element ordering code per catalog.hydac.com. Replaces Schroeder elements.
  • P=Polyester Fleece / CelluloseFilter media and collapse family as printed in the catalog.
  • 3 µmAbsolute filter rating per the HYDAC catalog.
  • 76.2 mmOutside diameter.
  • 124.5 mmElement length.
  • 10 barElement collapse (differential pressure) rating.
  • Nitrile (Buna-N)Seal compound.

Typical equipment & applications

  • HYDAC Betterfit drop-in replacement for Schroeder hydraulic filter elements
  • Return-line filtration for equivalent housings

Selection pitfalls — read before you substitute

  • A return-line element is not a pressure-line element: return cartridges (BN4HC low-collapse) tolerate roughly 20 bar differential, while BH4HC pressure executions are rated to 210 bar. Installing a low-collapse element in a pressure housing can rupture the media on cold-start spikes.
  • This execution carries an integral bypass valve (opens at 3 bar). The same envelope also exists without it, relying on the housing valve. Mixing the two strategies changes cold-start protection — match what was installed originally.
  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • Fine 3 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the 5.01.05 R 03 P filter element?
The published envelope is 76.2 mm OD × 124.5 mm length with a 26.6 mm inside diameter (3.000 × 4.902 in × 1.047 in ID). Confirm against the housing drawing before ordering.
What micron rating does 5.01.05 R 03 P use?
This element is rated 3 µm absolute — β5(c) ≥ 1000 per ISO 16889. Always compare Beta ratings at the same test point: two brands may print different micron numbers for the same physical grade.
What replaces the 5.01.05 R 03 P filter element?
3 partial match(es) requiring parameter review
How do I read the 5.01.05 R 03 P part number?
See the designation decoder above: each segment of 50105R03P encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 11 catalog element(s) share the 76×125 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

5.01.05 R 03 BN4 HYDAC · 3 µm 5.01.05 R 03 BN4 /-V HYDAC · 3 µm 5.01.05 R 05 BN4 HYDAC · 5 µm 5.01.05 R 10 BN4 HYDAC · 10 µm 5.01.05 R 10 BN4 /-V HYDAC · 10 µm 5.01.05 R 10 P HYDAC · 10 µm 5.01.05 R 10 P /-V HYDAC · 10 µm 5.01.05 R 20 BN4 HYDAC · 20 µm 5.01.05 R 25 P HYDAC · 25 µm 5.01.05 R 25 W HYDAC · 25 µm

Other models in the Betamicron 4 R series

All 929 →
0030 R 003 BN4HC 36×107 mm · 3 µm 0030 R 005 BN4HC 36×107 mm · 5 µm 0030 R 010 BN4HC 36×107 mm · 10 µm 0030 R 010 BN4HC /-B6 36×107 mm · 10 µm 0030 R 010 P/HC 36×107 mm · 10 µm 0030 R 010 P/HC /-B6 36×107 mm · 10 µm 0030 R 020 BN4HC 36×107 mm · 20 µm 0030 R 020 P/HC 36×107 mm · 20 µm 0030 R 025 W/HC 36×107 mm · 25 µm 0030 R 050 W/HC 36×107 mm · 50 µm

Reviewed & verified by the ElementRef engineering desk against HYDAC Technology Corporation on 2026-09-28. Read our editorial & correction policy.