ElementRef

MANN-FILTER · HD / WD Hydraulic · inline line

HD7050X filter element: specifications & equivalents

The HD7050X is a MANN-FILTER inline-line hydraulic filter element, sized 86 × 160 mm OD × length (ID 22 mm). Verify against the current manufacturer data sheet before ordering.

Envelope OD × L 86 × 160 mm
Inside diameter 22 mm
Line type inline
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-09-28. Confidence score 0.92.

Dimensions and comparison numbers are taken from the MANN-FILTER online catalog API. Beta rating, collapse pressure and seal material vary by execution — verify against the current MANN data sheet before ordering.

Specification table

ParameterValue
Filter type inline line
Outside diameter OD 86 mm
Inside diameter ID 22 mm
Length 160 mm
End caps open-ended cartridge element
Integral bypass valve none (housing/valve-dependent)
Manufacturer part no. HD7050X_MANN-FILTER
Source catalog MANN+HUMMEL / MANN-FILTER: MANN-FILTER online product catalog GraphQL API (mann-filter.com, store pcat_mf_en_store_en)
Last verified2026-09-28

Sources: MANN+HUMMEL / MANN-FILTER — MANN-FILTER online product catalog GraphQL API (mann-filter.com, store pcat_mf_en_store_en) — accessed 2026-09-27.

MANN-FILTER® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized MANN-FILTER distributor.

Dimensions & series range

Outside diameter86 mm (3.386 in)
Inside diameter22 mm (0.866 in)
Overall length160 mm (6.299 in)

All 86×160 mm interchange elements →

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ 0100MX010BN4H
page in verification queue
AftermarketpartialMANN-FILTER's online catalog lists 0100MX010BN4H (HYDAC) as a comparison number for HD7050X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ DHX100G10B3
page in verification queue
AftermarketpartialMANN-FILTER's online catalog lists DHX100G10B3 (FILTREC) as a comparison number for HD7050X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ HY13783
page in verification queue
AftermarketpartialMANN-FILTER's online catalog lists HY 13783 (SCHUPP / SF FILTER) as a comparison number for HD7050X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ SH70203
page in verification queue
AftermarketpartialMANN-FILTER's online catalog lists SH 70203 (HIFI-FILTER (JURA FILTRATION)) as a comparison number for HD7050X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.
↔ SH74448
page in verification queue
AftermarketpartialMANN-FILTER's online catalog lists SH 74448 (HIFI-FILTER (JURA FILTRATION)) as a comparison number for HD7050X. Envelope cross-reference; verify micron grade, collapse rating and seal configuration before substituting.

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the HD7050X model number is decoded

  • HD7050XMANN-FILTER hydraulic cartridge element part number.
  • 160 mmElement height (H).
  • 86 mmOuter diameter (A).
  • 22 mmInner diameter (B).

Typical equipment & applications

  • Replacement element for OEM hydraulic filter housings

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What are the dimensions of the HD7050X filter element?
The published envelope is 86 mm OD × 160 mm length with a 22 mm inside diameter (3.386 × 6.299 in × 0.866 in ID). Confirm against the housing drawing before ordering.
What replaces the HD7050X filter element?
5 partial match(es) requiring parameter review
How do I read the HD7050X part number?
See the designation decoder above: each segment of HD7050X encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Same-envelope elements from other brands

View full interchange →

These 1 catalog element(s) share the 86×160 mm envelope. Envelope match alone does not guarantee interchangeability — compare micron/Beta, seals and collapse rating.

HD7051X MANN-FILTER

Other models in the HD / WD Hydraulic series

All 880 →
HD10001 103×482 mm HD10002 99×177 mm HD10004 99×141 mm HD10006 99×155 mm HD10007 99×218 mm HD10008 99×218 mm HD10011X 99×210 mm HD10012X 99×330 mm HD10013 100×438 mm HD10014 99×155 mm

Reviewed & verified by the ElementRef engineering desk against MANN+HUMMEL / MANN-FILTER on 2026-09-28. Read our editorial & correction policy.