ElementRef

Pall · Coralon · inline line

HC8324FCN39HX321 filter element: specifications & equivalents

The HC8324FCN39HX321 is a Pall inline-line hydraulic filter element, built with glassfiber media. Verify against the current manufacturer data sheet before ordering.

Media glassfiber
Line type inline
Catalog verified. Parameters extracted from the manufacturer’s electronic catalog / official interchange document and checked 2026-10-01. Confidence score 0.90.

Pall's Lube & Hydraulic Crossover Tool prints removal rating, nominal length and seal only for elements — no OD, ID, collapse or bypass data. Verify envelope dimensions against the current Pall data sheet before ordering.

Specification table

ParameterValue
Filter type inline line
Media glassfiber
Integral bypass valve none (housing/valve-dependent)
Manufacturer part no. HC8324FCN39HX321
Source catalog Pall Corporation (Danaher): Pall Lube & Hydraulic Crossover Tool
Last verified2026-10-01

Sources: Pall Corporation (Danaher) — Pall Lube & Hydraulic Crossover Tool — accessed 2026-10-01.

Pall® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Pall distributor.

Cross references & equivalents

Equivalent modelBrandMatch levelNote
↔ HC8324FRN39ZPallfullPall Lube & Hydraulic Crossover Tool (manufacturer direct replacement).

Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the HC8324FCN39HX321 model number is decoded

  • HC8324FCN39HX321Pall element part number per the Pall Lube & Hydraulic Crossover Tool, with current Supralon replacement mapping.

Typical equipment & applications

  • Supralon hydraulic/lube-oil filter element per Pall’s official crossover mapping.

Selection pitfalls — read before you substitute

  • “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
  • Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
  • End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.

Frequently asked questions

What replaces the HC8324FCN39HX321 filter element?
1 catalog-confirmed full match(es) (HC8324FRN39Z)
How do I read the HC8324FCN39HX321 part number?
See the designation decoder above: each segment of HC8324FCN39HX321 encodes size, line type, filtration grade and media/collapse execution.
Is a same-envelope aftermarket element always a drop-in replacement?
No. Matching OD and length only proves the cartridge fits the bowl. End-cap style, seal compound, micron/Beta rating, collapse pressure and bypass configuration must also match; the table above tags every equivalent as full, partial or verify for exactly this reason.
How often should a hydraulic return-line element be replaced?
Replace at the housing manufacturer’s recommended differential-pressure setting (commonly signalled by a clogging indicator), or on a time-based service interval when no indicator is fitted — never wait for bypass to open continuously, because unfiltered oil then reaches the valves.

Other models in the Coralon series

All 2049 →
HC0008FCP11H 5 µm HC0030FCN3H HC0030FCS3H HC0082FCT18H 25 µm HC0101FAP18H 5 µm HC0101FCN18H 7 µm HC0101FCN18HY514 7 µm HC0101FCN18Z 7 µm HC0101FCN36H 7 µm HC0101FCN36Z 7 µm

Reviewed & verified by the ElementRef engineering desk against Pall Corporation (Danaher) on 2026-10-01. Read our editorial & correction policy.