Pall · Coralon · inline line
HC9600FCP4Z filter element: specifications & equivalents
The HC9600FCP4Z is a Pall inline-line hydraulic filter element, built with glassfiber media, rated at 5 µm absolute (βx(c)≥1000). Verify against the current manufacturer data sheet before ordering.
Pall's Lube & Hydraulic Crossover Tool prints removal rating, nominal length and seal only for Coralon elements — no OD, ID, collapse or bypass data. Verify envelope dimensions against the current Pall data sheet before ordering.
Specification table
| Parameter | Value |
|---|---|
| Filter type | inline line |
| Media | glassfiber |
| Filtration rating | 5 µm |
| Rating basis | absolute |
| Beta ratio | βx(c)≥1000 |
| Length | 101.6 mm |
| Nominal length code | 4 in |
| Integral bypass valve | none (housing/valve-dependent) |
| Seal material | Fluorocarbon (FKM) |
| Manufacturer part no. | HC9600FCP4Z |
| Source catalog | Pall Corporation (Danaher): Pall Lube & Hydraulic Crossover Tool |
| Last verified | 2026-10-01 |
Sources: Pall Corporation (Danaher) — Pall Lube & Hydraulic Crossover Tool — accessed 2026-10-01.
Pall® and all model designations are trademarks of their respective owners, used here for identification only — ElementRef is an independent reference site, not an authorized Pall distributor.
Dimensions & series range
| Overall length | 101.6 mm (4.000 in) |
| Nominal length code | 4 inches |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| ↔ HC9600FRP4Z | Pall | full | Pall Lube & Hydraulic Crossover Tool (manufacturer direct replacement). |
| ↔ SBF-9600-4Z3V | Schroeder Industries | partial | Schroeder online cross-reference (PALL); envelope match — verify grade and seals. |
Interchange levels: full catalog-confirmed drop-in · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the HC9600FCP4Z model number is decoded
- HC9600FCP4ZPall Coralon part number per the Pall Lube & Hydraulic Crossover Tool, with current Supralon replacement mapping.
Typical equipment & applications
- Coralon hydraulic/lube-oil filter element per Pall’s official crossover mapping.
Selection pitfalls — read before you substitute
- “10 µm nominal” and “12 µm at β1000” can describe the very same media — one is reported at β≥200, the other at β≥1000 per ISO 16889. Compare ratings at the same Beta test point, not just the printed micron number.
- Nitrile (NBR) seals are standard for mineral hydraulic oil but fail early in some phosphate-ester fluids and at sustained high temperature; verify seal compound against the fluid data sheet (fluorocarbon/Viton executions may be required).
- Fine 5 µm media loads faster and runs at a higher cold Δp than coarser grades — only downgrade cleanliness targets if the system ISO 4406 code allows it.
- End-cap geometry and the number/position of O-rings block interchange even when OD and length match — visually compare end caps before fitting, especially with aftermarket cartridges.
Frequently asked questions
What micron rating does HC9600FCP4Z use?
What replaces the HC9600FCP4Z filter element?
How do I read the HC9600FCP4Z part number?
Is a same-envelope aftermarket element always a drop-in replacement?
How often should a hydraulic return-line element be replaced?
Other models in the Coralon series
All 2049 →Reviewed & verified by the ElementRef engineering desk against Pall Corporation (Danaher) on 2026-10-01. Read our editorial & correction policy.